ISO REMCO definitions

ISO REMCO, the ISO committee responsible for guidance on reference materials within ISO,^[6] defines the following classes of reference material:^[7][8]

Reference Material

Material, sufficiently homogeneous and stable with respect to one or more specified properties, which has been established to be fit for its intended use in a measurement process.

Certified Reference Material

Reference material characterized by a metrologically valid procedure for one or more specified properties, accompanied by a certificate that provides the value of the specified property, its associated uncertainty, and a statement of metrological traceability.

Alternative terminology

Other bodies may define classes of reference material differently. WHO guidelines for biological^{[nb 1]} reference materials ^[9] provide the terms:^{[nb 2]}

• Reference standards: materials that are used as calibrators in assays
• International biological measurement standard: a biological substance provided to enable the results of biological assay or immunological assay procedures to be expressed in the same way throughout the world
• Secondary reference standards: Reference standards calibrated against and traceable to primary WHO materials and intended for use in routine tests
• Reference reagent: a WHO reference standard, the activity of which is defined by WHO in terms of a unit

For chemical substances some pharmacopoeias^[10] use the WHO terms^[11]

• Primary chemical reference substance: a chemical reference substance ... whose value is accepted without requiring comparison to another chemical substance.
• Secondary chemical reference substance: substance whose characteristics are assigned and/or calibrated by comparison with a primary chemical reference substance.

The United States National Institute of Standards and Technology (NIST) uses the trade marked term^[12] Standard Reference Material (SRM) to denote a certified reference material that satisfies additional NIST-specific criteria. In addition, commercial producers adhering to criteria and protocols defined by NIST may use the trademark ^[13] "NIST traceable reference material" to designate certified reference materials with a well-defined traceability linkage to existing NIST standards for chemical measurements. ^[14][15]

Principal steps in producing certified reference materials

The preparation of certified reference materials is described in general in ISO Guide 17034^[16] and in more detail in ISO Guide 35.^[17] Preparation of biological reference standards is described in WHO Guidance.^[9] General steps required in production of a certified reference material typically include:^[17]

• Collection or synthesis of material
• Sample preparation (including homogenization, stabilization, bottling etc.)
• Homogeneity testing
• Stability assessment
• Value assignment ("characterization" in ISO REMCO terms).^[18]

In addition it may be important to assess the commutability of a reference material; this is especially important for biological materials.^[9]

Sample preparation

Detailed sample preparation depends on the type of material. Pure standards are most likely to be prepared by chemical synthesis and purification and characterized by determination of remaining impurities.^[1] This is often done by commercial producers. Natural matrix CRMs (often shortened to 'matrix CRMs') contain an analyte or analytes in a natural sample (for, example, lead in fish tissue). These are typically produced by homogenization of a naturally occurring material followed by measurement of each analyte. Due to the difficulty in production and value assignment, these are usually produced by national or transnational metrology institutes like NIST (USA), BAM (Germany), KRISS (Korea) and EC JRC ( European Commission Joint Research Centre).

For natural materials, homogenization is often critical;^[19] natural materials are rarely homogeneous on the scale of grams so production of a solid natural matrix reference material typically involves processing to a fine powder or paste.^[20] Homogenization can have adverse effects, for example on proteins, so producers must take care not to over-process materials.^[9][17] Stability of a certified reference material is also important, so a range of strategies may be used to prepare a reference material that is more stable than the natural material it is prepared from.^{[21]: 119–124} For example, stabilizing agents such as antioxidants or antimicrobial agents may be added to prevent degradation, liquids containing certified concentrations of trace metals may have pH adjusted to keep metals in solution, and clinical reference materials may be freeze-dried for long term storage if they can be reconstituted successfully.^[9]: 96

Homogeneity testing

Homogeneity testing for a candidate reference material typically involves replicated measurements on multiple units or subsamples of the material.

Homogeneity tests for CRMs follow planned experimental designs. Because the experiment is intended to test for (or estimate the size of) variation in value between different CRM units, the designs are chosen to allow separation of variation in results due to random measurement error and variation due to differences between units of the CRM. Among the simplest designs recommended for this purpose is a simple balanced nested design (see schematic).

Typically 10-30 CRM units are taken from the batch at random; stratified random sampling is recommended so that the selected units are spread across the batch.^[22] An equal number of subsamples (usually two or three) is then taken from each CRM unit and measured. Subsamples are measured in random order.^[17][22] Other designs, such as randomized block designs, have also been used for CRM certification.^{[citation needed]}

Data processing for homogeneity tests usually involves a statistical significance test for evidence of differences between units of the candidate CRM. For the simple balanced design above, this typically uses an F test following ANOVA. A check for trends with production order is also recommended.^[22] This approach is not taken in ISO Guide 35:2017; rather, emphasis is placed on deciding whether the between-unit standard deviation is sufficiently small for the intended end use. If statistical tests are used, however, the homogeneity experiment should be capable of detecting important heterogeneity, ISO Guide 35:2017 in turn requiring a sufficient combination of precision of the measurement procedure, number of RM units and number of replicates per unit. Statistical power calculations can assist in ensuring a sufficiently effective test .^[17]

In extreme cases, such as microanalysis, materials must be checked for homogeneity on sub-micron scales; this may involve much larger numbers of observations and adjustments to statistical analysis.^[23]

Stability assessment