Classification by manufacturing process
Maki-e is roughly classified into three techniques of hira maki-e (平蒔絵), togidashi maki-e (研出蒔絵) and taka maki-e (高蒔絵) as a process classification. In Japan, these three techniques and shishiai togidashi maki-e (肉合研出蒔絵), which is a combination of togidashi maki-e and taka maki-e, are widely used.[1][2] These maki-e processes are started after the normal lacquerware process is finished. In other words, it is necessary to make a thick foundation layer of lacquer in advance by repeating a series of works such as coating the wood or paper with lacquer using a spatula or brush, drying it and polishing it.[3]
- Hira maki-e (平蒔絵)
At the first stage, a preliminary sketch process called okime is performed. After the original picture is drawn on the paper, thin washi is overlapped and copied along the outline from above, and then lacquer is applied to the outline drawn on the washi with a thin brush, and is pressed to the surface of the lacquerware to transfer. If the picture or pattern is simple, this process may be omitted. The next step, called jigaki, is the preparation process before metal powder is sprinkled. Lacquer is applied to the place where metal powder is to be sprinkled and it is used as an adhesive. Then, in a process called funmaki metal powder is sprinkled using a bird's feather shaft or a bamboo tube. In the next process, lacquer is applied on top of metal powder to protect the metal powder, and then the lacquer is dried. The first polishing is performed in the next funtogi process. The lacquer is slightly polished to expose only the surface of the metal powder with the metal powder embedded in the lacquer. In the subsequent polishing process, the entire lacquerware is polished with abrasives of different particle sizes. In addition, in the middle of each polishing process, a process called suriurushi is inserted, in which a series of processes of rubbing lacquer onto lacquerware and drying it are repeated. Glossy maki-e is completed through these complicated processes.[3] Although this technique is the simplest in maki-e, it was developed in the latter half of the Heian period after togidashi maki-e and completed in the Kamakura period because it was necessary to make the particles of metal powder finer. This technique was popular in the Azuchi-Momoyama period, when mass production of maki-e was necessary.[4][2]
- Togidashi maki-e (研出蒔絵)
Togidashi maki-e and hira maki-e have the same process up to the fungatame where they apply lacquer to protect the metal powder. However, the subsequent processes are different, and togidashi maki-e uses a process called nurikomi in which the entire lacquerware including pictures and patterns is coated with black lacquer. After drying, it is polished until the surface of the metal powder is exposed. After that, it is the same as hira maki-e in that it is polished with abrasives of different particle sizes, and lacquer is rubbed and dried, but the procedure of each process is different.[5] Since the entire surface including the pattern is coated with lacquer and then polished, the surface of the pattern and the background becomes smooth and metal powder is harder to fall off than hira maki-e. It was a technique developed and completed in the Heian period, and this technique was the mainstream of maki-e until the late Heian period when the refining technique of gold and silver powder was undeveloped and the particles were rough. Because a sword scabbard in the Nara period kept at Shōsōin uses a technique called makkinrusaku (末金鏤作) similar to this technique, it is sometimes said that Japanese maki-e began during the Nara period.[6][2]。
- Taka maki-e (高蒔絵)
A lacquer is mixed with charcoal or mineral particles to make a lacquer with increased viscosity, and a pattern is drawn on the surface to raise the pattern. Then it is dried and the same process as hira maki-e is done on top of the pattern to complete. The name of the technique is different depending on the kind of particles to be mixed, and the one mixed with charcoal powder is called sumikoage-taka maki-e (炭粉上蒔絵) and the one mixed with tin powder is suzuage-taka maki-e (錫上高蒔絵). This technique was developed in the middle of the Kamakura period. In the Muromachi period, sabiage-taka maki-e (錆上高蒔絵) was developed by mixing lacquer with powdered whetstone or powdered clay, and it became possible to raise the pattern higher.[7][2]。
- Shishiai togidashi maki-e (肉合研出蒔絵)
After raising the pattern in the process of taka mak-ie, it is completed through the process of togidashi maki-e. Unlike togidashi maki-e, the surface does not become smooth even after polishing because the process of taka maki-e is completed. It is the most complicated technique among maki-e, and was developed in the Muromachi period and was popular in the Edo period.[8]。