Bloc vote

The system requires two or more vacant seats for elections and is used for local elections in England and Wales. The original method and the one most commonly used is the following variety of bloc vote:

Electors vote for as many candidates as vacant seats in their geographic division of the election, or they may vote for fewer candidates. The elector cannot vote more than once for any candidate. A single vote for one of the candidates was known as a plumper, and was particularly valued by the candidate receiving it and would be sought or demanded when campaigning and offering hospitality especially from the most reliable supporters.

Example:

At the close of polls an impartial officer declares the poll-leading candidates to be elected to the vacant seats. If there are two seats (as above), the candidate with the most votes is elected, as is the candidate with the second-most votes. It is clear from the above example that the last-listed party can in principle have both its candidates elected in this area. However, if that party is only strong enough at best for second-place in this area it should have run one "rally around" candidate.

Drawbacks

This article possibly contains original research. (November 2021)

The system suffers from a drawback for a small minority of "ambitious electors" in an election. Say, a voter supports just one candidate but votes twice or more, but reluctantly, for these extra choices out of ignorance of the system or hatred for some other candidate(s). She estimates she has therefore done more to stop the 'threat' of the hated candidate(s) but she will have contributed to the defeat of her most preferred candidate by boosting the second preference, who may be the poll-topper or second-placer (if receiving strong local support), and local support has shifted or was to be expected to one of the hated or lower-order candidates who is also elected with the most or the second-most votes.^{[citation needed]}

Having two-or-greater seats per constituency Allows more fair elections than single-winner but only if a fair voting system is used. Using a multi-member district and a system that allows a minority to group to take all the seats, producing results just as un-proportional as single-winner FPTP.

Without the use of ranked votes or some mechanism to allocate the seats in a multi-seat district fairly, a party may choose to run only one candidate in a two-seat district, thus preventing it from winning two seats even if it has wide popularity. It will have "shot itself in the foot" by not running two candidates. It has given away such extra seats.

In first-past-the-post it is often the marginal seats, where the candidate wins by a narrow margin, that determine the outcome even if in the safe seats a party takes the vast bulk of votes.^{[citation needed]}

Limited vote

In 1868, the limited vote was introduced, which was similar to the bloc vote but restricted an individual elector in a three or four seat constituency to using up to one fewer vote than the number of seats to be filled.

The purpose of this innovation was to encourage minority representation and weaken political parties. In some areas, particularly the three member counties where rural elites were used to negotiating so as to minimise the number of contested elections, the reform worked as its proposers hoped. In some urban areas, the result was completely counterproductive.

Joseph Chamberlain and the Birmingham Liberal Caucus realised that by ensuring their supporters voted in a disciplined manner, as directed by the Caucus, they had enough support to win all three seats for the city. Instead of weakening party organisation, the limited vote strengthened it. Instead of providing guaranteed minority representation, the chance of it depended largely on how well the dominant local party organised itself.

When the Redistribution of Seats Act 1885 was being considered in 1884–85, the limited vote had little support. The redistribution eliminated the three and four member districts and the limited vote disappeared.

Single transferable vote

When Parliament debated the Fourth Reform Act in 1918, consideration was given to electoral reform. James Lowther was Chairman of the Speakers' Electoral Reform Conference in 1916–1917, of the Boundary Commissions (Great Britain and Ireland) in 1917, of the Royal Commission on Proportional Representation in 1918, all held before the legislation was introduced. There had been a call for the introduction of proportional representation in multi-member seats (Single transferable vote), at least in major urban areas where constituencies would not have to cover very large areas. This was not a unanimous recommendation, and some politicians wished to introduce the alternative vote in single member seats.

The House of Lords and House of Commons were agreed that there should be some reform, but could not agree what. In the end, Speaker Lowther warned that if the dispute continued the whole bill would be lost. As a result of this, neither the alternative vote or the single transferable vote (STV) were introduced for territorial constituencies which continued to use the old electoral system.

However one part of the proportional representation scheme survived into the final Act of Parliament. The multi-member University constituencies would elect their representatives by the single transferable vote.

As only one constituency had as many as three seats, the trial of STV was not very satisfactory, but it did loosen the traditional Conservative Party grip on most of the university seats and encouraged the election of Independents.

The university representation was abolished in 1950 (1920 in the case of Dublin University), so no members have since been elected on a proportional representation system.

Members of Parliament 1654-1658

Key to categories: BC - Borough/Burgh constituencies, CC - County constituencies, UC - University constituencies, EC - English constituencies, WC - Welsh constituencies, SC - Scottish constituencies, IC - Irish constituencies, EMP - English Members of Parliament, WMP - Welsh Members of Parliament, SMP - Scottish Members of Parliament, IMP - Irish Members of Parliament, Total MP - Total Members of Parliament.

Table 1: Constituencies by type

Table 2: Constituencies, by number of seats

Notes: (1) Monmouthshire (3 county seats) included in England, not Wales. (2) Dublin City and County treated as a county constituency (2 seats).

Members of Parliament 1708-1800

Key to categories in the following tables: BC - Borough/Burgh constituencies, CC - County constituencies, UC - University constituencies, Total C - Total constituencies, BMP - Borough/Burgh Members of Parliament, CMP - County Members of Parliament, UMP - University Members of Parliament.

Table 1: Constituencies and MPs, by type and country

Table 2: Number of seats per constituency, by type and country

Members of Parliament 1801-1821

Key to categories in the following tables: BC - Borough/Burgh constituencies, CC - County constituencies, UC - University constituencies, Total C - Total constituencies, BMP - Borough/Burgh Members of Parliament, CMP - County Members of Parliament, UMP - University Members of Parliament.

Monmouthshire (1 County constituency with 2 MPs and one single member Borough constituency) is included in Wales in these tables. Sources for this period may include the county in England.

Table 1: Constituencies and MPs, by type and country

Table 2: Number of seats per constituency, by type and country