The Mokai Tramway was a bush tramway constructed by the Taupo Totara Timber Company (TTT Co) to link their milling centre at Mokai with the New Zealand Government Railways line (NZR) at Putāruru in the Waikato region on the North Island of New Zealand. The more than 82 kilometres (51 mi) long light railway line was operated from 1903 to 1944 by the Taupo Totara Timber Company Tramway. It was handed over to NZR on 12 June 1950, and the section from Putāruru to Kinleith Mill south of Tokoroa is still being used for goods transport as of 2018.

This article includes a list of general references, but it lacks sufficient corresponding inline citations. (September 2018)

Quick Facts Technical, Track gauge ...

Mokai Tramway
Railway line of the Taupo Totara Timber Company showing "the corkscrew", with five different levels[1]
Technical
Track gauge	3 ft 6 in (1067 mm)
Route map Legend km from Hamilton (NZR) to Rotorua (NZR) 0,0 former transfer to the NZR network Taupo Totara Timber Co. in Putāruru Tokoroa 29,0 Kinleith Mill Waikato River The Spiral or The Corkscrew 82,0 Taupo Totara Timber Co. in Mokai Wooden tracks into the bush Fan like network in the bush

Close

The 82 kilometres (51 mi) long line was built in 1903 over the former Lichfield Branch line, which was originally built by the Thames Valley and Rotorua Railway Company to be part of the line to Rotorua. The TTT Co line then went onwards south of Lichfield through what is now Tokoroa and Kinleith and crossed the Waikato River at Ongaroto.

At Ongaroto the company built a large timber bridge of locally sourced totara, designed by Public Works Department engineer Frederick Furkert. In later years this timber bridge deteriorated and was condemned, but the company could not afford to replace it immediately because its sawmill had burned down in 1928. In the last few years of service, trains arriving at the bridge would stop and the passengers and fireman would walk across while the driver gently opened the throttle and then jumped off. The train would slowly ease across the bridge before being stopped on the other side by the fireman, where everyone would reboard the train. This bridge was replaced in 1931 by a steel truss bridge with a central pier.^[2]

In general the TTT Co line was constructed to a fairly high standard for a bush tramway, with 1 in 30 grades and 30 metre radius curves. This reflected the company's ultimate intention to sell the line to NZR. In 1911 the TTT Co put forward a proposal to extend their line from Mokai into Taupo township via Oruanui. However, considerable objection was made to this proposal by the people of Rotorua.^[3] The Taupo District Railway League consequently lodged a complaint to the Member of Parliament for the district, William MacDonald, protesting the opposition being made by the Rotorua Chamber of Commerce. As time passed the proposal for the TTT Co scheme was eventually shelved.

The TTT Co line eventually closed on 26 October 1944. However the Government saw that the line had greater potential and in September 1946 acquired the first 29 km between Putāruru and Kinleith. This section of line opened again on 9 June 1947 under the control of the Public Works Department using steam locomotives purchased from the TTT Co.^[4]

Around the same time plans were being made for a large pulp and paper mill to be constructed at Kinleith. The line with its sharp curves, steep grades and light rails, needed to be significantly upgraded to enable heavy traffic. Reconstruction of the line began in 1949, reducing grades from 1 in 44 to 1 in 70 and curves from 201 metre radius to 322 metre radius. The rebuilt line was handed over to NZR on 12 June 1950.^[5]

The section from Putāruru to Kinleith Mill south of Tokoroa is still⁽²⁰¹⁸⁾ being used as part of the Kinleith Branch Line for goods transport.

• Taupo railway proposals