The RC-5 protocol was developed by Philips in the early 1980s as a semi-proprietary consumer IR (infrared) remote control communication protocol for consumer electronics. It was subsequently adopted by most European manufacturers, as well as by many US manufacturers of specialty audio and video equipment. The other main protocol relevant to consumer electronics is the NEC protocol, which is largely used by Japanese manufacturers.

This article needs additional citations for verification. (November 2016)

This article or section may need to be formatted. (July 2014)

The RC-5 protocol, when properly implemented, has the advantage that any CD handset (for example) may be used to control any compatible brand of CD player. By comparison, the NEC protocol assigns each brand its own unique header(s) after which may follow any desired command set; this confers the advantage that there cannot be any interference between remote handsets for pieces of equipment made by different manufacturers.

The basics of the protocol are well known. The handset contains a keypad and a transmitter integrated circuit (IC) driving an IR LED.^[1] The command data is a Manchester-coded bitstream modulating a 36 kHz carrier. (Often the carrier used is 38 kHz or 40 kHz, apparently due to misinformation about the actual protocol.)^{[clarification needed]} The IR signal from the transmitter is detected by a specialized IC with an integral photo-diode, and is amplified, filtered, and demodulated so that the receiving device can act upon the received command.^[2] RC-5 only provides a one-way link, with information travelling from the handset to the receiving unit.

The command comprises 14 bits:

• A start bit which is always logic 1 and allows the receiving IC to set the proper gain.
• A field bit which denotes whether the command sent is in the lower field (logic 1 → 0 to 63 decimal) or the upper field (logic 0 → 64 to 127 decimal). Originally a second start bit, the field bit was added later by Philips when it was realized that 64 commands per device were insufficient. Many devices still use the original system.
• A control bit which toggles with each button press. This allows the receiving device to distinguish between two successive button presses (such as "1", "1" for "11") as opposed to the user simply holding down the button and the repeating commands being interrupted by a person walking by, for example.
• A five-bit system address that selects one of 32 possible systems.
• A six-bit command that (in conjunction with the field bit) represents one of the 128 possible RC-5 commands.

The 36 kHz carrier frequency was chosen to render the system immune to interference from TV scan lines. Since the repetition of the 36 kHz carrier is 27.778 μs and the duty factor is 25 %, the carrier pulse duration is 6.944 μs. Each bit of the RC-5 code word contains 32 carrier pulses, and an equal duration of silence, so the bit time is 64×27.778 μs = 1.778 ms, and the 14 symbols (bits) of a complete RC-5 code word take 24.889 ms to transmit. The code word is repeated every 113.778 ms (4096 ÷ 36 kHz) as long as a key remains pressed. (Again, please note that these timings are not strictly followed by all manufacturers, due to a lack of widespread distribution of accurate information on the RC-5 protocol.)

While the RC-5 protocol is well known and understood, what is not so well documented are the system number allocations and the actual RC-5 commands used for each system. The information provided below is the most complete and accurate information available at this time. It is from a printed document from Philips dated December 1992 that is unfortunately not available in electronic format (e.g., PDF), nor is an updated version available. This information is provided so that companies that wish to use the RC-5 protocol can use it properly, and avoid conflicts with other equipment that may or may not be using the correct system numbers and commands.

The information in the tables on this page is known to be accurate. Yet it is also clear that there are many gaps in these tables. For example, there is no category listing for DVD players in the system table. (They were not developed until five years after the date of publication of the material from which this information was obtained.) It would obviously be useful therefore to expand these tables with known accurate information. At this time, there are only a few possible ways to do so.

The first would be to capture the IR bitstream from the handset of newer Philips products, such as DVD players and analyze them to see what system number is used. The other would be to use the popular Philips Pronto series of programmable remote controls. These can be programmed to operate Philips components using the RC-5 protocol. Again, the bitstream output of the handset would need to be captured and analyzed. The only other way is to obtain the appropriate documents directly from Philips.

As can be seen, this information is out of date. There are no longer any systems using CD-Video or CD-Photo, for example. In addition, many of the "Reserved" system numbers have no doubt been allocated by Philips during the intervening 16 years. In order to maintain compatibility, it would be helpful to obtain this information. Unfortunately, this has proven to be difficult.

When designing a product using the RC-5 protocol, the designer must follow the published information as closely as possible. For example, one surround-sound processor from a US specialty manufacturer used the system number 16, designated for "Preamp 1". This caused many problems with home theater installations that also included a separate two-channel preamplifier, which if of US or European origin, would also use the RC-5 protocol with system number 16. If the designers of the surround-sound processor had the correct information available to them, it would have been obvious that a better choice would have been to use system number 19, designated for "Preamp 2", as this would have avoided needless conflict between products.

Over time, the information will also be added for the command tables so that all of the available information regarding the RC-5 protocol is gathered in one place. The information in the command tables shown in standard font was obtained from the Philips publication referenced at the bottom of this page. Information in italics is information that is known to be accurate, as it was derived by one of the methods described above.

^† Commands for video extension systems 3 (TV) and 9 (VCR) which use the common video command numbers are given in Tables 4b (TV) and 7b (VCR).

• Remote control
• Consumer IR

• Remote Control System RC-5 Including Command Tables, Philips Semiconductors, December 1992, Publication No. 9388 706 23011